License Plates

Enquire About What Other Stock And Chrome Variations Are Available

Series Features

  • Australian Design Rules (ADR) approved.
  • Low current draw.
  • Fully sealed to meet the demands of the transport & marine industries.
  • Epoxy sealed electronics for environmental & vibration protection.
  • Polycarbonate construction.
  • Multi-voltage.
  • Lifetime Warranty.
Specifications
Voltage: 12-24V
Light Source: LED
Lens: Polycarbonate
Body: ABS
Approvals: ADR
Wire Length: 450mm
 
 

 

Part No. EA26800-BB
Voltage 12-24V
Colour Stop-Tail/Indicator/Reverse
Description Only one required for ADR
Cable Length: 450mm

 

License Plate Lamps - 76mm x 42mm x 30mm
  • 35BLM
  • 35BLMB
  • 35CLM
  • 35CLMB
  • 35BLM1P
  • 1 metre of cable with plug
  • 35BLM6
  • 6 metre of cable hard wire
Product Description: The 35 series licence plate lamps are fully submersible and shock proof. Also available with 6 metres of hard wired cable or with 1 metre ending in a plug which clips into the back of the 100, 150 and 275 series Generation II lamps.
Part No 35BLM 35BLMB 35CLM 35CLMB 35BLM1P 35BLM6
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt
Cable: 40cm 40cm 40cm 40cm 1 Metre with plug 6 Metre with plug
Packaging: Blister of 1 Poly bag of 1 Blister of 1 Poly bag of 1 Blister of 1 Poly bag of 1
Current: @13.8Volts (Licence-0.04Amps) - @28Volts (Licence-0.04Amps).
C.R.N: (Licence 36280)
Fitting: Fit onto flat surface, 25mm from top centre, long edge of licence plate with lens facing towards the ground. Refer to ADR 13/00 for fitting instructions.
Compliance: ADR / ECE approved
Warranty: 5 year warranty

 

License Plate Lamps - 65mm x 30mm x 24mm, 69mm x 54mm x 40mm

 

  • 30BLM
  • 6434BWM
  • 30CLM
  • 6434CWM
  • 65362 No ADR
Product Description: The 30 series (6434) licence plate lamps are fully submersible, shock resistant and are suited for the budget conscious consumer. Can also be used for general illumination. Illumination lamp, can be
used as a courtesy lamp.
Part No 30BLM 6434BWM 30CLM 6434CWM 65362
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt 12 Volt
Cable: 14cm 14cm 14cm 14cm 40cm hard wired
Packaging: Blister pack of 2 Poly bag of 1 Blister pack of 2 Poly bag of 1 Poly bag of 1
Current: @13.8Volts (Licence-0.02Amps) - @28Volts (Licence-0.03Amps) @13.8Volts (0.11Amps)
C.R.N: (Licence plate lamps 40511) N/A
Fitting: Run wires through hole in flat fitting surface, ensure foam gasket is between lamp and surface, fix using screws sup- plied. You will require one lamp on the left and right side of the licence plate. Please refer to ADR 13/00. Fit onto flat surface using bolts in assembly.
Compliance: ADR / ECE approved DOT / SAE approved
Warranty: 5 year warranty 5 year warranty

 

License Plate Lamps - 375mm x 173mm x 25mm
  • LP1
  • LP1B
  • LP1 with Sample of a Licence plate fitted, shown active.
Product Description: The licence plate frame allows the licence plate to be fitted underneath the two licence plate lamps all in one housing. Comes with 1 metre of cable ending in a plug which clips into the back of the 100, 150 and 275 series Generation II lamps.
Part No LP1 LP1B
Voltage: 12-24 Volt 12-24 Volt
Cable: 1 metre 1 metre
Packaging: Blister of 1 Box of 1
Current: @13.8Volts (Licence-0.11Amps) - @28Volts (Licence-0.07Amps)
C.R.N: (Licence plate lamp 39611)
Fitting: Fixes into same screw pattern as standard Australian licence plate, then wire clips into back of Generation II lamp. Fit up to 1 metre away from lamps.
Compliance: ADR / ECE approved
Warranty: 5 year warranty

 

40 Series License Plate Lamp - 70mm x 42mm x 40mm
  • 41BLM
Product Description: LED Technologies have released an updated Licence Plate Lamp into their range. Featuring a tough polycarbonate lens with an ABS base for extra durability and four super bright SMD LEDs, this lamp will surely impress. They come standard in Multivolt 12-24 volt with 23cm of hard wired cable and are backed by a 5 year warranty. One lamp on the long edge of a licence plate is required for ADR compliance (with ECE approval) which make them a very economical alternative. The 40 series licence plate lamps are perfect for any vehicle or trailer application where licence illumination is required.
Part No 41BLM - Blister Single
41BLMB - Bulk Poly Bag
Voltage: Multivolt 12-24V
Packaging: Blister Pack of 1
Current: @13.8V - 0.05A
@28V - 0.04A
Warranty: 5 Years